ToneHarbor

Photos from current listings. Actual item, color, and included accessories may vary.

Eminence LEGEND BP 1525 Buying Guide

The Eminence Legend BP 1525 is a 15-inch, 8-ohm bass guitar speaker designed for high-power, low-frequency reinforcement in vented cabinets. The core trade-off for buyers is voice-coil thermal capacity versus low-frequency extension: higher power handling (700W) requires a 2.5-inch coil and stiffer suspension, which trades some deep-bass sensitivity for durability. Choose a 2.5-inch VC bass woofer only if your amp delivers 350–700W RMS and your cabinet is tuned for a 15-inch driver; skip it for low-wattage combos or sealed boxes.

Nominal Diameter:15 in / 381 mmPower Handling:700W RMSImpedance:8 ohmVoice Coil:2.5 in / 64 mm
Typical price range$169.99

At a glance

Brand
Not synced yet
Model
Not synced yet
MPN
Not synced yet
Category
Instrument Accessories
Status
Offers available
Data updated
Nov 16, 2026

Current offers

Highlights

  • 2.5-inch voice coil diameter is the thermal bottleneck; 700W RMS handling assumes a vented cabinet with adequate port velocity and crossover above 40 Hz.
  • 8-ohm nominal impedance lets a single 15-inch driver present a safe load to most bass heads, but parallel pairs drop to 4 ohms—verify your amp's minimum before wiring.
  • Legend BP series uses a pressed-steel frame and treated paper cone; this is a bass-guitar voiced woofer, not a full-range PA speaker or subwoofer.
  • 2.5-inch VC bass woofers deliver higher power compression resistance than 2-inch coil models, but they need cabinet tuning (Fs ~40 Hz) to avoid mid-bass hump.

Best use cases

  • Best fit: a 15-inch vented bass cabinet build rated 400–700W RMS with a port tuned near 40 Hz; the BP 1525 handles fundamental notes without cone breakup.
  • Best fit: replacing a blown 15-inch bass driver in a combo or extension cab where the existing baffle cutout is 15 inches and the amp is 8-ohm compatible.
  • Wrong fit: sealed or small closed cabinets—the stiff suspension and high Qts of high-power bass woofers produce weak, boomy low end without a ported alignment.
  • Wrong fit: low-wattage tube combos under 100W; the 700W thermal rating is wasted, and the driver's low sensitivity may reduce volume versus a lighter 15-inch speaker.

Buying tips

  • Match amp RMS to driver RMS: a 700W speaker pairs safely with a 350–700W bass head; underpowering below 50% RMS risks clipping damage to the voice coil.
  • Confirm the baffle cutout diameter is 14.0–14.25 inches for a 15-inch frame; measure the existing cabinet before ordering, as 15-inch speakers are not drop-in universal.
  • Check cabinet internal volume: a single 15-inch bass woofer typically needs 2.5–4.0 cubic feet vented; smaller boxes will choke low-frequency output.
  • Verify impedance wiring: one 8-ohm BP 1525 is safe on most amps; two in parallel = 4 ohms, so confirm your head is 4-ohm stable before adding a second cab.

Specs

Nominal Diameter15 in / 381 mm
Power Handling700W RMS
Impedance8 ohm
Voice Coil2.5 in / 64 mm

Alternatives to compare

Related searches

What to check before buying

  • Measure your cabinet's baffle hole—it must be 13.9 inches—and confirm the mounting screw pattern matches a standard 15-inch frame.
  • Calculate net cabinet volume and port tuning; the BP 1525 is designed for vented alignment, not sealed or aperiodic boxes.
  • Confirm your amplifier's power output at 8 ohms does not exceed 700W RMS per driver and that its minimum impedance matches your wiring.
  • Check that your cabinet's internal depth clears the driver's rear magnet and frame depth, and that the baffle can support the woofer's weight.

FAQ

All Instrument Accessories buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.