ToneHarbor

Photos from current listings. Actual item, color, and included accessories may vary.

Eminence LEGEND BP 122 Buying Guide

The Eminence Legend BP122 is a 12-inch, 8-ohm bass guitar speaker rated at 500W RMS with a 2-inch voice coil, designed as a drop-in upgrade for bass combos and extension cabinets. The key trade-off is power handling versus sensitivity: high-wattage bass drivers trade some efficiency for thermal headroom, so match the driver to your amp's real output and cabinet tuning rather than chasing wattage alone.

Driver Type:12" bass guitar woofer, portedImpedance / Power:8 ohm, 500 W RMS / 1000 W peakBaffle Cutout:11.08 in (281 mm)Voice Coil / Motor:2 in VC, 10.55 Tm BL
Typical price range$139.99

At a glance

Brand
Not synced yet
Model
Not synced yet
MPN
Not synced yet
Category
Instrument Accessories
Status
Offers available
Data updated
Nov 16, 2026

Current offers

Highlights

  • 500W RMS power rating with 2-inch voice coil delivers thermal headroom for high-output bass heads without cone breakup at stage volume.
  • 8-ohm impedance matches most bass amp outputs and allows pairing in parallel for 4-ohm loads when using two cabinets.
  • 12-inch bass-optimized cone and suspension are tuned for low-frequency extension, unlike generic PA or guitar woofers.
  • Legend BP series uses a treated paper cone and cloth surround for durability under sustained low-frequency excursion.

Best use cases

  • Best fit: upgrading a 1x12 or 2x12 bass cabinet where the existing driver is blown or underpowered — choose the BP122 for 8-ohm replacement.
  • Best fit: building a compact bass extension cab for a head rated up to 500W per channel — one BP122 per cab in parallel gives a 4-ohm total load.
  • Wrong fit: sealed or undersized guitar-style cabs — the BP122 needs a ported or properly tuned bass enclosure to avoid excessive cone excursion and thin low end.
  • Skip if: you need high sensitivity for low-wattage tube amps — a lower-power, higher-SPL bass driver will produce more volume per watt than this 500W-rated unit.

Buying tips

  • Match amp RMS output to speaker RMS, not peak wattage: a 500W RMS driver pairs safely with heads up to 500W RMS per cab.
  • Use the 2-inch voice coil as a thermal benchmark — 1.5-inch coils in budget bass speakers heat-soak faster under sustained low notes.
  • Confirm the cabinet cutout and bolt pattern accept a standard 12-inch frame before ordering; most 12-inch bass cabs use a 4-bolt or 8-bolt pattern.
  • For two-cab rigs, wire two 8-ohm BP122 drivers in parallel to present a 4-ohm load — verify your head is rated for 4 ohms minimum.

Specs

Driver Type12" bass guitar woofer, ported
Impedance / Power8 ohm, 500 W RMS / 1000 W peak
Baffle Cutout11.08 in (281 mm)
Voice Coil / Motor2 in VC, 10.55 Tm BL

Alternatives to compare

Related searches

What to check before buying

  • Measure the existing baffle cutout: it must be 11.08 inches (281 mm) in diameter, and confirm the driver's outer frame clears any bracing or grille.
  • Verify amplifier impedance compatibility: 8 ohms for a single driver, 4 ohms for two in parallel—check the head's minimum load before wiring.
  • Confirm the cabinet is ported and calculate internal volume plus port dimensions to tune near 45–55 Hz; sealed or undersized boxes are a mismatch.
  • Check mounting depth and clearance behind the baffle for the magnet and frame, especially in shallow combo cabinets.

FAQ

All Instrument Accessories buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.